Concrete cutting in Marysville WA - clean openings cut where you need them
A broken panel, a pipe under the slab or a wall that needs a door. We scan, cut clean lines and leave your site tidy.
- Licensed and fully insured.
- Free quotes on site.
- Expect a reply within 1 business day.
How do you cut concrete without breaking what's around it?
Concrete cutting in Marysville, WA means sawing straight, controlled lines through a slab or wall so one section can come out cleanly and the concrete around it stays sound, whether that's a broken driveway panel, a trench for a pipe or an opening in a basement wall.
We're based in Marysville and take jobs in Everett, Lake Stevens, Arlington, Mill Creek and the other cities around it. Most people who call us need one piece of concrete gone and the rest left alone. The price mostly comes down to how many feet of cut there are, how thick the slab or wall is, whether there's rebar inside, which is the steel that holds the concrete together, and whether you want us to break out and haul the pieces or just saw the lines. The schedule turns on what's buried in the concrete, because we scan before we saw, and on whether a permit or a utility locate has to come first. Your written estimate spells out which of those apply to your job.
How do you know your slab or wall needs cutting?
One cracked driveway panel
One section of your driveway is broken or sunk while the rest still sits flat. That piece can usually be cut out along clean lines and replaced on its own, but waiting lets the edges crumble and water get under the good panels next to it.
A line under the slab
You need a new drain or water line run across a garage floor or patio, or you have a leak somewhere underneath. That usually means sawing a trench, and a leak left alone keeps washing out the dirt the slab sits on.
A wall that needs an opening
You want a door, a window or a pass-through for a pipe in a concrete wall. If the room gets finished first, the water and dust from cutting land on new drywall and floors, so it's better to cut before the finish work.
How we handle concrete cutting, start to finish
We start by scanning the slab or wall, because what's buried in the concrete, like rebar, pipes or wiring, decides where it's safe to cut. Then we mark the lines, saw them with water running over the blade to keep the dust down, and vacuum up the slurry, the gray mud that water and concrete dust make, as we go. If your quote includes removal, we break out the pieces inside the cuts, haul them off and leave clean edges ready for whatever comes next.
Most cuts are the first half of a bigger job. We cut out cracked or sunken panels ahead of concrete driveway building so the new section meets the old one along a straight edge, and we saw back an old slab to make room for concrete patio construction when you're widening or reshaping one.
Cutting only
This suits you if you already have a crew or a plan for the broken pieces, since we saw the lines and leave the panels in place. Our part of the job stays small, but the heavy work of breaking and hauling is still waiting for someone.
Cutting, breakout and haul-off
This suits most homeowners, because you end up with a clean opening and nothing left sitting in the yard. I'd pick it unless you already know who's taking the concrete, since those pieces are heavier and harder to get rid of than most people expect.
Get a written quote for your concrete cut
Send the form and we'll reply within one business day to set a time for me to come out. The on-site quote is free, there's no obligation, and you get a written estimate showing what's included.
(360) 251-0089- Based in
- Marysville, WA 98270
- Hours
- Mon–Fri: 7 AM–9 PM, Sat–Sun: 6 AM–9 PM
What happens after you ask us to cut concrete?
From your first call to the final walk-through, here's what you do, what I do and what our crew does on a cutting job.
Tell us about the cut
Call (360) 251-0089 or send the form with where the cut goes, roughly how thick the slab or wall is and whether you want the pieces hauled off. That tells me what to look for when I come out.
I measure and write it up
I come out, measure and ask what the opening or trench needs to do, then send a written estimate. It says plainly what's in it and what isn't, including whether breaking out and hauling are covered, so you know what you're paying for before we start.
We scan, then cut
Once you say go, we sort out any permit questions and scan the concrete before the saw touches it. Our small crew does the cutting and breakout, and I'm on site with them.
Cleanup and a walk-through
We vacuum up the slurry, sweep the dust and haul off whatever the quote covers. Then I walk the job with you so you can see the edges before we leave.
Why Marysville homeowners call Classic Marysville Concrete for cutting
The owner comes out to measure
I usually come out myself to look at the job and measure, and I'm on site with the small crew I've worked with for years when we cut. You're talking to the person who'll actually be standing next to the saw.
Tricky cuts since 2017
We've been in business since 2017, and the cuts I like best are the ones nobody's tried before, like a doorway through an old basement wall or a trench across a garage floor. Around Marysville a lot of those calls come from houses being opened up for an addition or a new line, so we're used to working around what's already there.
Fully insured while the saw runs
We're licensed and fully insured, which matters on a cut because the saw is working inside a slab or wall your house depends on. Satisfaction guaranteed on every job.
If you've got a cut in mind, send us the details and I'll set up a time to come take a look.
Cutting concrete for driveways, patios and walls in Marysville
Whether a cut needs a permit depends on the job, so I'll tell you early if one may come into yours and which office covers your address, since that can be the city or the county. Inside the city, Marysville Building Services reviews plans for code compliance, and Engineering Services reviews right-of-way permits, which can matter when a driveway cut reaches toward the street. We can help with the application and work to any inspections that come with it.
When a trench has to be dug after the cut, Washington's Dig Law requires a call to 811, or a request at digsafewashington.com, at least two business days before anyone digs, not counting weekends and legal holidays, so the locate request needs to go in early. Slurry gets the same care. Guidance in an older edition of the state Ecology department's stormwater manual calls for vacuuming slurry and cuttings during the work and keeping them off pavement overnight and out of storm drains, which can mean covering the catch basin near your curb for a while. Dust is the other half of it, because the state Department of Labor & Industries requires controls like vacuum attachments when workers breathe more silica dust than its limits allow, so we cut wet or with a vacuum on the saw. We work to the same rules on jobs in Everett and Lake Stevens.
Questions about concrete cutting in Marysville
How much does concrete cutting cost per foot in Marysville?
Saw cutting a concrete slab usually costs about $4 to $15 per linear foot across the US, and that covers the sawing itself. Reinforced or deeper slabs usually cost more per foot than an easy-to-reach slab, and on a small job a minimum or trip charge can outweigh the per-foot rate, so ask for the full job price. My written estimate gives you that full price for your job.
Does the price of cutting concrete include hauling it away?
Not always, because sawing and removal are separate jobs and some cutters saw the lines and leave the panels where they are. Breaking, hauling and disposal can add more than the sawing itself, so check what a quote covers. Ours says in writing whether we're only cutting or also breaking out and hauling.
Why do you scan a slab before cutting it?
Because what's buried in the concrete decides whether a cut is safe. One field guide calls for a scan before any cut to find rebar, live electrical conduit and post-tension cables, steel cables pulled tight inside some slabs, since cutting one releases that tension all at once and can collapse the slab. That's why the scan comes before the saw on our jobs.
Where do I apply for a building permit in Marysville?
All building permit applications in Marysville go through the city's Permit Portal. If your address falls under the county instead, I'll tell you that when I come out to measure.
How do I cut a doorway into a concrete basement wall?
An opening in a concrete wall is usually cut with a track-mounted wall saw, the standard tool for vertical cuts. One field guide says any structural opening, or any cut through structural reinforcement, needs the structural engineer of record, the engineer responsible for the building's design. If the wall holds up your house, bring that engineer in before we start.
What is the best way to cut very thick concrete?
Very thick concrete is usually cut in several passes with a saw, or with a wire saw for the thickest or oddest-shaped sections. A walk-behind saw only reaches so deep in one pass, and a wire saw, a diamond-studded wire pulled through the concrete, takes longer to set up, so it mostly pays off on very thick concrete. On a thick slab, ask which approach the crew plans.
Related concrete work that often follows a cut
Concrete driveway building
Once a broken section is cut out, new concrete goes back in on a packed base so the patch sits level with the rest of the driveway.
Concrete patio construction
If you're widening a patio or replacing a tired one, cutting a clean edge first lets the new slab meet the house and yard where you want it.
Cities where we cut concrete
Classic Marysville Concrete is based in Marysville, WA, and we cut slabs and walls across the cities around it, from Arlington to Mill Creek. The 12 cities below each have their own page, and they aren't the only places we work.
Marysville, WA
Send us the spot you need cut
If you know of anything under or behind the concrete, like a floor drain or an old pipe, tell us up front so I can plan the scan before I come out.